消防水炮是現在應用較多的一類自動滅火設備，那么關于消防水炮滅火系統工作方式以及安裝事項您有了解嗎？接下來一起來看看資訊吧。

Fire water monitor is a kind of automatic fire extinguishing equipment which is widely used now. Do you know about the working mode and installation of fire water monitor fire extinguishing system? Next, let's take a look at the information.

消防水炮滅火系統工作方式

Working mode of fire water monitor fire extinguishing system

火災探測部位的雙波段探測器或光學截面探測器報警后，空間定位精度高的雙波段火災探測器定位點火點，信息處理主機通知自動火災處理后的戰斗信號。水炮驅動自動消防水炮對空間火點進行掃描鎖定，自動將消防水炮對準火源。

After the dual band detector or optical section detector at the fire detection position gives an alarm, the dual band fire detector with high spatial positioning accuracy locates the ignition point, and the information processing host notifies the battle signal after automatic fire processing. The water monitor drives the automatic fire water monitor to scan and lock the space fire point, and automatically aim the fire water monitor at the fire source.

前端水流量指示器的反饋信號和泵房壓力繼電器的開度信號顯示在控制室的控制臺上。當主機報警結束時，會自動關閉消防泵和消防電動蝶閥。

The feedback signal of the front-end water flow indicator and the opening signal of the pump room pressure relay are displayed on the console in the control room. When the alarm of the main engine ends, the fire pump and fire electric butterfly valve will be automatically closed.

消防中心收到火災報警系統發出的火災報警信號后，消防中心值班人員將通過系統強制切換的彩色視頻圖像進一步確認消防控制室。將火炮調火點，啟動消防泵，打開電動閥，實施灑水滅火。

After the fire control center receives the fire alarm signal sent by the fire alarm system, the personnel on duty of the fire control center will further confirm the fire control room through the color video image forcibly switched by the system. Adjust the gun to the fire point, start the fire pump, open the electric valve and spray water to extinguish the fire.

現場人員找到火點后，操作相應火炮下方的現場手動控制面板，直接調節火炮對準火點，開火抽水并打開電動閥，實施灑水滅火，同時向消防部門發送報警信號控制中心。

After finding the fire point, the on-site personnel operate the on-site manual control panel under the corresponding gun, directly adjust the gun to aim at the fire point, fire and pump water, open the electric valve, spray water to extinguish the fire, and send an alarm signal to the fire department to the control center at the same time.

消防水炮滅火系統安裝

Installation of fire water monitor fire extinguishing system

安裝火災探測器。在探測器的保護范圍（視野）內不應有障礙物。探測器應水平安裝。當必須傾斜安裝時，傾斜角度不應大于45°C。

Install fire detectors. There shall be no obstacles within the protection range (field of view) of the detector. The detector shall be installed horizontally. When inclined installation is necessary, the inclination angle shall not be greater than 45 ° C.

安裝火災自動監測儀前，應完成供水管網的水壓強度和密封性試驗，同時完成管網沖洗；火災自動探測器與墻壁的距離不應妨礙火災自動探測器的轉動；

Before installing the automatic fire monitor, the water pressure strength and tightness test of the water supply pipe network shall be completed, and the pipe network flushing shall be completed at the same time; The distance between the automatic fire detector and the wall shall not hinder the rotation of the automatic fire detector;

短冒口應固定牢固，在自動噴槍進氣法蘭下方10厘米處設置固定點；電動閥、水流指示器和閘閥水平安裝；火炮掃描范圍內不應有影響火炮動作和操作的障礙物；

The short riser shall be fixed firmly, and a fixed point shall be set 10 cm below the air inlet flange of the automatic spray gun; Horizontal installation of electric valve, water flow indicator and gate valve; There should be no obstacles affecting the action and operation of the artillery within the scanning range of the artillery;

川消消防水炮現場控制面板應安裝在便于操作的位置。操作現場控制面板時，應注意數控消防的運動方向和停止位置，并應清楚觀察水炮；火警的連接電纜應捆扎牢固。

The on-site control panel of Chuanxiao fire monitor shall be installed at a position convenient for operation. When operating the on-site control panel, pay attention to the movement direction and stop position of NC fire fighting, and clearly observe the water monitor; The connecting cable of fire alarm shall be tied firmly.

消防水炮滅火系統工作方式以及安裝事項便是這樣了，如果您想了解更多關于消防設備的信息，就來關注川消網站www.xintli.net吧，為您做詳細解答。

The working mode and installation of fire water monitor fire extinguishing system are like this. If you want to know more about fire-fighting equipment, please pay attention to www.xintli.net COM, for you to do a detailed answer.