消防炮快速滅火的使用原理
來源：http://www.xintli.net/ 日期：2022-05-18
在消防行業，消防炮是很多設計單位和消防施工單位常用的消防設備。它采用紅紫外檢測和數字圖像處理技術，檢測火災發生時產生的火焰、溫度等自動跟蹤定位，并采用自動控制方式實現消防。那么消防炮是如何滅火的呢？
In the fire-fighting industry, fire monitor is a common fire-fighting equipment used by many design units and fire-fighting construction units. It uses red and ultraviolet detection and digital image processing technology to detect the flame and temperature generated in the event of fire, and automatically track and locate, and uses automatic control to realize fire control. So what about fire guns?
消防炮的工作原理是通過前端探測系統采集現場紅外圖像，控制器采用圖像處理的手段對發生在控制區域內的火災進行偵測和定位，這樣的設計便于消防炮打開相應的聯動設備并控制水炮進入噴水滅火操作。消防炮的炮由底座、進水管、回轉體、集水管、射流調節環、手把和鎖緊機構等組成，炮身可作水平回轉和仰俯回轉，并可實現定位。
The working principle of the fire monitor is to collect the on-site infrared image through the front-end detection system, and the central controller uses the means of image processing to detect and locate the fire in the control area. This design is convenient for the fire monitor to open the corresponding linkage equipment and control the water monitor to enter the sprinkler operation. The gun of the fire monitor is composed of a base, a water inlet pipe, a rotating body, a water collecting pipe, a jet adjusting ring, a handle and a locking mechanism. The gun body can rotate horizontally and pitching, and can realize positioning.
消防炮這樣的設計有什么特點呢？這樣設計使得消防炮的使用壓力范圍廣，射程遠并可實施直流90°開花、水霧射流的無極調節。其重量輕、體積小、功能全、滅火效果好，使該炮的特點。
What are the characteristics of the design of fire monitor? This design enables the fire monitor to have a wide range of application pressure and long range, and can realize the stepless adjustment of DC to 90 ° flowering and water mist jet. Its light weight, small volume, full function and good fire extinguishing effect make the gun unique.
自動火炮是如何滅火的，也是很多消防行業新手和智能火炮新手都想知道的。它由水裝置和智能滅火裝置控制器、解碼器/現場控制箱、現場控制面板或無線遙控器組成。自動火災監測儀本身有一個紅色和紫外線雙波段探測器。
How automatic artillery extinguishes fire is also what many novices in the fire industry and intelligent artillery want to know. It is composed of water device and intelligent fire extinguishing device controller, decoder / field control box, field control panel or wireless remote controller. The automatic fire monitor itself has a red and ultraviolet dual band detector.
當檢測到火災時，向火災監控主機發送報警信號，然后主機向自動滅火報警系統發送報警信號。火災自動監測儀主體可與現場區域控制相連，通過現場區域控制箱可對水炮進行控制和操作，現場區域控制箱可手動控制瞄準和滅火。
When a fire is detected, it sends an alarm signal to the fire monitoring host, and then the host sends an alarm signal to the automatic fire extinguishing alarm system. The main body of the automatic fire monitor can be connected with the on-site area control. The water cannon can be controlled and operated through the on-site area control box, and the on-site area control box can manually control aiming and fire extinguishing.
當發現火災時，火災自動監測器會立即啟動，智能掃描火源，在很短的時間內確定火源的具體位置。瞄準火源射水滅火。火源撲滅后，智能滅火裝置控制器會發出停止噴水指令。如果發現新的火源，智能滅火裝置控制器將重復上述過程，待所有火源撲滅后返回監控狀態。
When a fire is found, the automatic fire monitor will start immediately to intelligently scan the fire source and determine the specific location of the fire source in a very short time. Aim at the fire source and shoot water to extinguish the fire. After the fire source is extinguished, the intelligent fire extinguishing device controller will issue a stop spraying command. If a new fire source is found, the intelligent fire extinguishing device controller will repeat the above process and return to the monitoring state after all fire sources are extinguished.
山東川消建議平常使用中應經常檢查噴槍的完整性和操作靈活性。 如發現緊固件松動，應及時修理，使噴槍保持良好的工作狀態。 噴水操作時，松開鎖緊螺釘，調整噴槍的噴射方向和角度，然后將壓力增加到使用壓力。 轉動射流調節環可實現水直流轉開花，或開花轉直流。 每次使用后，應用清水噴灑一段時間，然后將槍內的水排干。 如有必要，應在管道中安裝排水閥。
In normal use, the integrity and operation flexibility of the spray gun should be checked frequently. If the fastener is found to be loose, it shall be repaired in time to keep the spray gun in good working condition. When spraying water, loosen the locking screw, adjust the spraying direction and angle of the spray gun, and then increase the pressure to the service pressure. Rotating the jet adjusting ring can realize water DC to flowering or flowering to DC. After each use, spray with clean water for a period of time, and then drain the water in the gun. If necessary, drain valves shall be installed in the pipeline.
The use principle of fire monitor for rapid fire extinguishing is explained above. If you need or are interested in it, please directly follow this website www.xintli.net Com for more information.
