川消七氟丙烷滅火系統控制器操作與故障處理
來源：http://www.xintli.net/ 日期：2022-12-31
當七氟丙烷滅火系統出現故障的時候我們要怎么去處理，其實這個更考驗使用者的心態了。今天
川消小編就為大家提供七氟丙烷滅火系統控制器操作與故障處理說明。
When the heptafluoropropane fire extinguishing system fails, how do we deal with it? In fact, it tests the mentality of users. Today, the Sichuan Xiaobian Department will provide instructions on the operation and troubleshooting of heptafluoropropane fire extinguishing system controller.
控制器操作與故障處理說明
Description of controller operation and troubleshooting
1.開機：打主電和備電開關。
1. Start up: turn on the main power and standby power switches.
2.開子鎖：按一下鍵盤操作鍵，再按一下調分鍵，鍵盤鎖燈亮允許操作。
2. Open the sub lock: press the keyboard operation key once, and then press the scoring down key, and the keyboard lock light is on to allow operation.
3.火警：主控制器顯示任一回路火警，馬上派人員到現場察看：
3. Fire alarm: the main controller displays any loop fire alarm, and immediately send personnel to the site to check:
①確認是火警：馬上手動啟動系統按防護區門口的緊急啟動按鈕。
① Confirm it is a fire alarm: start the system manually immediately and press the emergency start button at the entrance of the protection area.
②如果被確認為誤報：按防護區門口的緊急停止鍵，再把誤報警排除主控制器復位緊急停止按鈕復位。
② If it is confirmed as a false alarm: press the emergency stop button at the door of the protection area, and then eliminate the false alarm. Reset the emergency stop button of the main controller.
4.故障：主控制器顯示故障信號，看主機面板顯示的是什么故障：
4. Fault: the main controller displays the fault signal, and see what fault is displayed on the host panel:
①主電：看是否停電。
① Main power: check whether there is power failure.
②備電：看備用電池連接線是否松開。
② Standby power: check whether the backup battery cable is loosened.
③回路故障：到防護區看探測器有沒有松落。
③ Circuit fault: go to the protection area to see if the detector is loose.
④掉載故障：電磁閥連線有沒有松開。
④ Load loss fault: whether the solenoid valve wiring is loose.
5.手動操作：如發現防護區發生火警，探測器還沒有發生動作時，就需要現場人員手動啟動系統。
5. Manual operation: If a fire alarm is found in the protection area and the detector has not yet acted, the on-site personnel shall manually start the system.
①直接按防護區門口的緊急啟動按鈕。
① Directly press the emergency start button at the door of the protection area.
②主控制器面板上也有緊急啟動按鈕，直接按下就可以。
② There is also an emergency start button on the main controller panel, which can be directly pressed.
以上就是七氟丙烷滅火系統控制器操作與故障處理說明啦，如果你還想更詳細的了解七氟丙烷滅火系統就關注我們的網站
http://www.xintli.net咨詢吧！
The above is the instructions for the operation and troubleshooting of the heptafluoropropane fire extinguishing system controller. If you want to know more about the heptafluoropropane fire extinguishing system, please follow our website http://www.xintli.net Consult!
