消防泵故障的3大問題了解處理
來源：http://www.xintli.net/ 日期：2022-12-28
消防泵顧名思義，消防上用的泵，廣泛應用于、水處理、消防等部門，是用來抽送各類液體，是創建無泄漏、無污染文明車間、文明工廠的理想用泵與消防系統的。下面
川消小編來講講消防泵故障的3大問題了解處理。
As the name implies, fire pumps are widely used in environmental protection, water treatment, fire protection and other departments. They are used to pump all kinds of liquids. They are ideal pumps and fire protection systems for creating leak free, pollution-free and civilized workshops and factories. Now let's talk about the three major problems of fire pump failure.
問題一：消防泵震動嚴重
Problem 1: The fire pump vibrates severely
1.消防泵與電機軸不同心？
1. The fire pump is not concentric with the motor shaft?
調正，對準消防泵與電機軸心。
Align the fire pump and motor shafts.
2.消防泵軸彎曲？
2. The fire pump shaft is bent?
拆下校直或換新的。
Remove the straightening or replace it with a new one.
3.葉輪不平衡？
3. Impeller is unbalanced?
拆下找平衡。
Remove for balancing.
問題二：消防泵抽不出液體
Problem 2: The fire pump cannot pump out liquid
1.壓出管路太細，管路損失太大？
1. The pressed out pipeline is too thin, and the pipeline loss is too large?
換適合的壓出管路。
Replace with a suitable press out pipe.
2.使用揚程超過了設計揚程？
2. Does the operating lift exceed the design lift?
重新選消防泵。
Reselect the fire pump.
3.吸入管或消防泵內沒有排凈氣體？
3. Is there no gas discharged from the suction pipe or fire pump?
檢修吸入管路并排凈氣體。
Maintain the suction pipe and discharge the gas.
4.吸上高度超過允許范圍？
4. Does the suction height exceed the allowable range?
按允許吸上高度重新安裝消防泵。
Reinstall the fire pump according to the allowable suction height.
5.輸送熱的、揮發性的介質？
5. Conveying hot and volatile media?
降低吸程或采用倒灌按裝。
Reduce the suction head or use reverse filling.
6.轉向反了？
6. The steering is reversed?
糾正轉向。
Correct the steering.
7.沒有灌注液體？
7. No liquid filled?
重新灌消防泵。
Recharge the fire pump.
8.吸入管、出水管或消防泵的流道堵塞？
8. Is the flow passage of suction pipe, outlet pipe or fire pump blocked?
雜物。
Eliminate sundries.
問題三：機械密封泄漏嚴重
Problem 3: Serious mechanical seal leakage
1.固定螺釘松動，使彈簧失去作用？
1. The fixing screw is loose, causing the spring to lose its function?
緊固螺釘或重新調整彈簧。
Tighten the screws or readjust the springs.
2.彈簧壓力不足？
2. Insufficient spring pressure?
重新調整彈簧壓縮量或換彈簧。
Readjust the spring compression or replace the spring.
3.靜環裝配歪斜？
3. Static ring assembly is skewed?
重裝消防泵用靜環。
Refit the static ring for the fire pump.
4.動換或靜環端面腐蝕、磨損或刮傷？
4. Is the end face of the moving or stationary ring corroded, worn or scratched?
修復或更換壞的動環靜環。
Repair or replace the damaged dynamic and static rings.
5.軸套加工精度和光潔度不夠，影響了動環的軸向移動？
5. The machining accuracy and finish of the shaft sleeve are not enough, which affects the axial movement of the moving ring?
換加工精度合格的軸套。
Replace the shaft sleeve with qualified machining accuracy.
6.雜質、異物或介質結晶影響了動環的軸向移動或支撐在動、靜環的端面之間？
6. Do impurities, foreign matters or medium crystals affect the axial movement of the moving ring or support between the end faces of the moving and stationary rings?
雜質、異物和結晶，清洗密封元件。
Eliminate impurities, foreign matters and crystals, and clean the sealing elements.
7.動環密封圈裝配斜卷或腐蝕變形？
7. Rotating ring seal ring assembly is inclined or corroded and deformed?
重裝或更換消防泵用動環密封圈。
Reassemble or replace the movable ring seal ring for the fire pump.
此外消防泵的選型應根據消防泵應用工程的工藝流程，給排水要求，從液體輸送量、裝置揚程、液體性質、管路布置以及操作運轉條件等方面加以考慮。更多相關內容就來我們網站
http://www.xintli.net進行咨詢吧！
