川消消防泵四大常見問題及辦法
來源：http://www.xintli.net/ 日期：2022-10-25
消防泵是保障消防的重要設施，清楚地了解消防泵的問題，并針對性地掉這些問題，才能保障消防泵的長久有效地使用。和
川消小編一起來看看消防泵常見的四大問題。
Fire pump is an important facility to ensure fire safety. Only by clearly understanding the problems of fire pump and solving these problems, can we ensure the long-term and effective use of fire pump. Check the four common problems of fire pumps with Chuanxiao Xiaobian.
問題一
Question 1
消防泵震動嚴重
Serious vibration of fire pump
1.消防泵與電機軸不同心，調正，對準消防泵與電機軸心。
1. The fire pump is not concentric with the motor shaft, so it is aligned with the fire pump and motor shaft.
2.消防泵軸彎曲，拆下校直或換新的。
2. The fire pump shaft is bent, remove and straighten it or replace it with a new one.
3.葉輪不平衡，拆下找平衡。
3. The impeller is unbalanced, remove it for balancing.
問題二
Question 2
消防泵抽不出液體
The fire pump cannot pump out liquid
1.壓出管路太細，管路損失太大，換適合的壓出管路。
1. The press out pipeline is too thin and the pipeline loss is too large. Replace it with a suitable press out pipeline.
2.使用揚程超過了設計揚程，重新選消防泵。
2. If the service lift exceeds the design lift, re select the fire pump.
3.吸入管或消防泵內沒有排凈氣體，檢修吸入管路并排凈氣體。
3. The suction pipe or fire pump is not completely vented, and the suction pipe shall be overhauled and the gas shall be vented.
4.吸上高度超過允許范圍，按允許吸上高度重新安裝消防泵。
4. If the suction height exceeds the allowable range, reinstall the fire pump according to the allowable suction height.
5.輸送熱的、揮發性的介質，降低吸程或采用倒灌按裝。
5. To transport hot and volatile media, reduce the suction head or use reverse filling.
6.轉向反了，糾正轉向。
6. The steering is reversed. Correct the steering.
7.沒有灌注液體，重新灌消防泵。
7. Recharge the fire pump if there is no liquid.
8.吸入管、出水管或消防泵的流道堵塞，雜物。
8. The suction pipe, outlet pipe or the flow passage of the fire pump are blocked to eliminate debris.
問題三
Question 3
機械密封泄漏嚴重
Serious mechanical seal leakage
1.固定螺釘松動，使彈簧失去作用，緊固螺釘或重新調整彈簧。
1. The fixing screw is loose, making the spring lose its function. Tighten the screw or readjust the spring.
2.彈簧壓力不足，重新調整彈簧壓縮量或換彈簧。
2. If the spring pressure is insufficient, readjust the spring compression or replace the spring.
3.靜環裝配歪斜，重裝消防泵用靜環。
3. The static ring assembly is skewed, and the static ring for fire pump is reinstalled.
4.動換或靜環端面腐蝕、磨損或刮傷，修復或更換壞的動環靜環。
4. The end face of the moving or stationary ring is corroded, worn or scratched, and the damaged moving or stationary ring is repaired or replaced.
5.軸套加工精度和光潔度不夠，影響了動環的軸向移動，換加工精度合格的軸套。
5. The processing accuracy and finish of the shaft sleeve are not enough, which affects the axial movement of the moving ring. Replace the shaft sleeve with a qualified processing accuracy.
6.雜質、異物或介質結晶影響了動環的軸向移動或支撐在動、靜環的端面之間，
6. Impurities, foreign matters or medium crystallization affect the axial movement of the moving ring or support between the end faces of the moving and stationary rings,
雜質、異物和結晶，清洗密封元件。
Eliminate impurities, foreign matters and crystals, and clean the sealing elements.
7.動環密封圈裝配斜卷或腐蝕變形，重裝或更換消防泵用動環密封圈。
7. The moving ring seal ring is assembled obliquely or corroded and deformed. Reinstall or replace the moving ring seal ring for fire pump.
問題四
Question 4
消防泵用電機過熱
Motor for fire pump overheated
1.填料壓蓋壓的太緊或機械密封彈簧調的太緊，重新調整壓蓋或機械密封的彈簧壓縮量。
1. If the packing gland is pressed too tightly or the mechanical seal spring is adjusted too tightly, readjust the spring compression of the gland or mechanical seal.
2.使用范圍(流量、揚程)超過消防泵的設計要求，按系列型譜選合適的電機。
2. If the scope of use (flow and lift) exceeds the design requirements of the fire pump, select the appropriate motor according to the series type spectrum.
3.消防泵裝配質量差，有摩擦處或電機與消防泵軸不同心，檢查裝配質量，排除裝配故障。
3. The assembly quality of the fire pump is poor. If there is friction or the motor is not concentric with the fire pump shaft, check the assembly quality and eliminate the assembly failure.
4.介質比重超過消防泵的配置電機，配置合適的消防泵用電機。
4. If the specific gravity of the medium exceeds that of the fire pump, the motor shall be equipped with a suitable fire pump motor.
川消消防泵四大常見問題及辦法就是以上所講解的內容了，希望對您有所幫助，您如果有什么問題或者需求要滿足的，歡迎來我們網站
http://www.xintli.net咨詢了解！
The four common problems and solutions of Chuanxiao fire pump are explained above. I hope they can help you. If you have any problems or needs to meet, welcome to our website http://www.xintli.net Ask about it!
