消防水炮常見故障的三種情況
來源：http://www.xintli.net/ 日期：2022-10-17
隨著消防水炮的普及，故障也時有聽說，那么常見的消防水炮故障是什么呢？如何這個故障問題？下面就跟著
川消小編一起來分析一番吧。
With the popularity of fire water monitors, failures have been heard from time to time. What are the common failures of fire water monitors? How to solve this problem? Now let's follow Chuan Xiaobian to analyze it.
消防水炮常見故障的一種情況：從水炮口噴出的水既不是柱形也不是霧狀。
A common fault condition of fire water monitor: the water sprayed from the nozzle is neither columnar nor foggy.
當出現這種情況時，一般都會認為是水炮的產品質量有問題，可事實卻不是，這是因為在安裝消防水炮繼電器設備時，沒有安裝過濾網，才導致消防管道內被殘渣堵塞，從而出現以上情況。處理方法是改裝過濾網，清理管道中的殘渣。如果殘渣被堵塞在系統的鎮流器中時，也會出現以上情況。此時，須找到制造商的技術人員進行。
When this happens, it is generally believed that the product quality of the water monitor is defective, but the fact is not. This is because when the relay equipment of the fire monitor is installed, the filter screen is not installed, which leads to the blockage of the fire pipe by residues, thus the above situation occurs. The treatment method is to refit the filter screen and clean the residue in the pipeline. If the residue is blocked in the ballast of the system, the above situation will also occur. At this time, the manufacturer's technicians must be found to solve the problem.
消防水炮常見故障二種情況：當系統工作時，離心水泵啟動后，管道內的工作壓力卻達不到。
There are two common failures of the fire water monitor: when the system is working, the working pressure in the pipeline cannot be reached after the centrifugal pump is started.
因為消防水炮要實現有效射程，其管道中的工作壓力須達到額定壓力值。如果工作壓力太低，就會出現噴射距離短，無法達到額定射程。因此，這種情況通常是由于管道中氣體過多或吸濕水泵底閥無法正常打開造成的，處理方法是對這兩部分進行排查。
Because in order to achieve an effective range, the working pressure in the pipeline of the fire monitor must reach the rated pressure value. If the working pressure is too low, the injection distance will be short and the rated range will not be reached. Therefore, this situation is usually caused by too much gas in the pipeline or the bottom valve of the moisture absorption pump cannot be opened normally. The treatment method is to check these two parts.
常見的消防水炮故障三種情況：消防控制室不能遠程啟動離心泵。一般來說，這種情況可以行路線排查維修，如果真的出現引路或短路故障，當然會出現無論怎么操作，離心泵系統都不會啟動。還有一種情況是聯動操控琴臺按鈕出現故障也會導致上述情況發生。處理方法是對主機按鈕或實際操作盤進行維修。
There are three common cases of fire water monitor failure: the fire control room cannot remotely start the centrifugal pump. Generally speaking, in this case, the route can be checked and repaired first. If there is a lead or short circuit fault, of course, no matter how you operate, the centrifugal pump system will not start. Another case is that the failure of the linkage console button will also lead to the above situation. The handling method is to repair the host button or the actual operation panel.
Here are three common failures of the fire water monitor. If you have any questions, please come to our website at any time http://www.xintli.net Consult!
