川消滅火器的年檢規定與要點
來源：http://www.xintli.net/ 日期：2022-08-19
實際上堅持滅火器定期維護和到期報廢是為了確保滅火器的使用，以及及時有效地?fù)錅绯跗鸹馂?zāi)，減少火災隱患，保護人身和財產。下面
川消小編就來講講滅火器的年檢規定與要點內容吧。
In fact, the purpose of insisting on regular maintenance and scrapping of fire extinguishers is to ensure the safe use of fire extinguishers, timely and effectively extinguish the initial fire, reduce fire hazards, and protect personal and property safety. Let's talk about the annual inspection regulations and key points of fire extinguishers.
滅火器年檢規定
Regulations on annual inspection of fire extinguisher
不同類型的滅火器年檢時間也是不同的。具體而言，手提式和推車式二氧化碳滅火器期滿五年，以后每隔二年，須進行水壓試驗等檢查。
The annual inspection time of different types of fire extinguishers is also different. Specifically, the portable and wheeled carbon dioxide fire extinguishers shall be subject to hydrostatic test and other inspections every two years after the expiration of five years.
手提式和推車式機械泡沫滅火器、手提式清水滅火器期滿三年，以后每隔二年，須進行水壓試驗檢查。手提式和推車式化學泡沫滅火器、手提式酸堿滅火器期滿二年，以后每隔一年，須進行水壓試驗檢查。
Portable and wheeled mechanical foam fire extinguishers and portable clean water fire extinguishers shall be subject to hydrostatic test and inspection every two years after the expiration of three years. Portable and wheeled chemical foam fire extinguishers and portable acid-base fire extinguishers shall be subject to hydrostatic test and inspection every other year after the expiration of two years.
滅火器在每次使用后，須送到已取得維修許可證的維修單位檢查，更換已損件，重新充裝滅火劑和驅動氣體。
After each use, the fire extinguisher must be sent to the maintenance unit that has obtained the maintenance permit for inspection, replaced with damaged parts, and refilled with fire extinguishing agent and driving gas.
滅火器年檢時，需要檢查的項目比較多，如：檢查筒體是否有生銹、變形等現象，還要看銘牌是否是否清晰。其次是看噴嘴有無變形、開裂，噴射軟管是否會發生堵塞，這些問題都要及時處理。
During the annual inspection of fire extinguisher, there are many items to be inspected, such as whether the cylinder is rusted and deformed, and whether the nameplate is clear. Secondly, check whether the nozzle is deformed and cracked, and whether the spray hose is blocked. These problems should be handled in time.
滅火器年檢要點要有哪些
What are the key points of annual inspection of fire extinguishers
1、滅火器和車一樣，每年都需要年檢，所以當滅火器使用一年之后，就要送去檢測單位檢查，防止出現問題。購買時，也要注意日期，還要看上面的標簽，標簽上都會注明上次年檢的時間。
1. Like cars, fire extinguishers need annual inspection every year. Therefore, when the fire extinguisher is used for one year, it should be sent to the testing unit for inspection to prevent problems. When you purchase, you should also pay attention to the date and the label on it. The label will indicate the time of the last annual inspection.
2、年檢時，主要是檢查它的外表是否完好，有無開裂，有無生銹、掉漆等問題，這是比較重要的一點。
2. During the annual inspection, it is mainly to check whether its appearance is intact, whether there is crack, whether there is rust, paint falling and other problems. This is an important point.
3、還要看滅火器的插銷是不是出現腐蝕或損壞，如果有出現這些問題，就要及時更換。
3. It is also necessary to check whether the safety pin of the fire extinguisher is corroded or damaged. If these problems occur, they should be replaced in time.
4、在年檢時重要的一點，就是要仔細看壓力表，檢查壓力是否正常。如果檢測出壓力太小，說明滅火器失效了，如果滅火器壓力過大，很有可能會爆炸，這些情況都是不的，需要及時處理。
4. An important point during the annual inspection is to carefully look at the pressure gauge and check whether the pressure is normal. If the pressure is detected to be too low, it means that the fire extinguisher has failed. If the pressure of the fire extinguisher is too high, it is likely to explode. These conditions are unsafe and need to be handled in time.
每個滅火器都有保質期，在筒體上都有注明，因此使用時要注意日期，一旦發現滅火器過期了，就要停止使用，送到維修單位進行測量檢查。如果有問題的話，要及時更換新的，才能保證使用。更多相關事項就來我們網站
http://www.xintli.net咨詢吧！
Each fire extinguisher has a shelf life and is marked on the cylinder. Therefore, pay attention to the date when using. Once the fire extinguisher is found to be expired, it should be stopped and sent to the maintenance unit for measurement and inspection. If there is any problem, it should be replaced in time to ensure safe use. For more information, please visit our website http://www.xintli.net Consult!
