川消消防壓力開關怎樣接線
來源：http://www.xintli.net/ 日期：2022-08-02
消防壓力開關的接線，需要注意的細節是比較多的，不可會出問題。而消防壓力開關怎樣接線，現在我們一起來看看吧。
There are many details to be paid attention to in the wiring of the fire pressure switch, so there should be no problems. Now let's have a look at how to connect the fire pressure switch.
川消消防壓力開關怎樣接線
How to connect Chuanxiao fire pressure switch
1、先使用萬用表，將消防壓力開關的常開點給測量出來，然后接入到模塊中的X1和X2常開端子上。注意，消防開關是有4個線的，其中兩根常開點和兩根常閉點。
1. First use a multimeter to measure the normally open point of the fire pressure switch, and then connect it to the X1 and X2 normally open terminals in the module. Note that the fire switch has four wires, including two normally open points and two normally closed points.
2、要是模塊選型不對的話，只需將壓力開關使用輸入模式便可以了。這里的區別是，輸入模塊是可以不用DC24V電壓的，也不存在外控的輸出端子。
2. If the module selection is wrong, just use the input mode of the pressure switch. The difference here is that the input module can not use DC24V voltage, and there is no external control output terminal.
3、壓力開關是屬于整個消防設備中的主要配件，是需要將其安裝于噴淋系統的報警閥上。
3. The pressure switch is the main accessory of the whole fire-fighting equipment, which needs to be installed on the alarm valve of the sprinkler system.
What should be paid attention to in the use of Chuanxiao fire switch
1、消防壓力開關的重要性是比較大的，當噴淋管道中的壓力是比較供水的壓力更小的話，則壓力開關會啟動，同時將產生的動作信號傳送到報警系統中，這樣控制設備在接收到信息之后，便會進行加壓工作。
1. The importance of the fire-fighting pressure switch is relatively large. When the pressure in the spray pipe is smaller than that of the water supply, the pressure switch will start and transmit the generated action signal to the alarm system, so that the control equipment will pressurize after receiving the information.
2、消防系統中的輸入模塊，也被叫做是監視模塊，是用于檢查設備是否能夠正常工作。只要常開信號設備出現動作，被監視到后，常開端便會出現
2. The input module in the fire protection system, also known as the monitoring module, is used to check whether the equipment can work normally. As long as the normally open signal equipment acts and is monitored, the normally open signal will appear
3、當報警閥在出現動作之后，報警管路是會通水的，而管內的壓力在超過了設定好的數值之后，開關便會出現啟動，并往系統傳達報警閥工作。
3. When the alarm valve acts, the alarm pipeline will be filled with water, and after the pressure in the pipe exceeds the set value, the switch will start and convey the work of the alarm valve to the system.
4、為了預防工作人員的誤操作，導致閥門出現關閉的情況，造成系統無法工作。就會在閥門上安裝信號的反饋設備，防止出現誤操作。
4. In order to prevent the valve from closing due to the misoperation of the staff, resulting in the system unable to work. Signal feedback equipment will be installed on the valve to prevent misoperation.
消防壓力開關怎樣接線，以及消防開關使用需注意什么的問題就先介紹到這里了，各位是否了解了呢。消防壓力開關的接線是不可出錯的，否則會影響到后期正常使用。您有什么問題就來我們網站
http://www.xintli.net咨詢吧。
How to connect the fire pressure switch and what should be paid attention to in the use of the fire switch are introduced here first. Have you understood it. The wiring of the fire pressure switch must not be wrong, otherwise it will affect the later normal use. Come to our website if you have any questions http://www.xintli.net Consult.
