川消壓力開關從安裝到工藝性能的經
來源：http://www.xintli.net/ 日期：2022-07-15
壓力開關的功能是檢測、顯示、報警和控制信號輸出，確保系統正常運行，通過高速MCU收集和處理數據，內置精密傳感器進行補償，是檢測壓力和液位信號，實現壓力和液位監測和控制的高精度設備。廣泛應用于化工、機械、水文、電力、等測量氣液壓力的自化系統。由于調節方便靈活，安裝簡單，可替代大多數使用液位開關的場合。
The function of the pressure switch is to detect, display, alarm and control signal output to ensure the normal operation of the system. It collects and processes data through high-speed MCU, and is compensated by built-in precision sensors. It is a high-precision equipment to detect pressure and liquid level signals and realize pressure and liquid level monitoring and control. It is widely used in automatic systems for measuring gas-liquid pressure in chemical industry, machinery, hydrology, electricity, environmental protection, etc. Due to convenient and flexible adjustment and simple installation, it can replace most occasions where liquid level switches are used.
安裝：
Installation:
1.請遵守緊固力矩。
1. Please observe the tightening torque.
2.使用面板安裝連接器裝卡時，請不要對壓力開關/傳感器控制器施加過大的應力。
2. Please do not exert too much stress on the pressure switch / sensor controller when using the panel to install the connector.
3.請不要掉落、敲打、施加沖擊。
3. Please do not fall, knock or impact.
4.使用市場銷售的開關電源時，請接地FG端子。
4. When using the switching power supply sold in the market, please ground the FG terminal.
5.不要強力拉伸導線以及導線提拉產品本體（拉伸強度49N以內）。
5. Do not stretch the wire and lift the product body with strong force (the tensile strength is within 49n).
6.當雜物可能混入流體時，請在一次側(流入測試)設置過濾器和分離器，并配管。
6. When sundries may be mixed with fluid, please set filters and separators on the primary side (inflow test) and piping.
配線：
Wiring:
1.
川消小編提醒您，請不要強力拉伸導線。特別是組裝管接頭和配管時，不要攜帶壓力開關的導線。
1. Chuanxiao Xiaobian reminds you not to stretch the wire. Especially when assembling pipe joints and piping, do not carry the wires of pressure switches.
2.不要反復彎曲拉伸導線，承載重物，施加力。
2. Do not bend and stretch the conductor repeatedly, carry heavy objects and apply force.
3.請勿使用與動力線和高壓線相同的配線路徑。
3. Do not use the same wiring path as the power line and high voltage line.
4.請確認配線的絕緣體。
4. Please confirm the insulator of the wiring.
5.使用模擬輸出時，請在產品和開關電源之間添加電噪聲過濾器。
5. When using analog output, please add an electric noise filter between the product and the switching power supply.
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.xintli.net , our staff will contact you in time.
