川消電控消防水炮的使用與維護
來源：http://www.xintli.net/ 日期：2022-07-12
消防器材在我們的生活中是非常常見的，為我們的生活提供了保障。但是大家對消防器材的分類可能不是很了解，今天就由電控消防水炮廠家為大家講一下電控消防水炮的詳細內容，以及保養的相關事項，希望對大家能有所幫助。
Fire fighting equipment is very common in our life, which provides a guarantee for our life. But you may not know much about the classification of fire-fighting equipment. Today, the manufacturer of electric control fire water monitor will tell you the details of electric control fire water monitor and related maintenance matters, hoping to help you.
一、電控消防水炮使用
1、 Use of electric fire water monitor
1、根據火場的實際情況及火災的性質，選擇使用水炮的直流或噴霧功能。
1. According to the actual situation of the fire and the nature of the fire, choose to use the DC or spray function of the water cannon.
2、向上鍵是操作炮頭向上運動，向下鍵是操作炮頭向下運動，向左鍵是操作炮體向左運動，向右鍵是操作炮體向右運動，啟動鍵是開啟水炮進水電動閥門，停止鍵是關閉水炮進水電動閥門。
2. The up key is to operate the gun head to move up, the down key is to operate the gun head to move down, the left key is to operate the gun body to move left, the right key is to operate the gun body to move right, the start key is to open the water cannon water inlet electric valve, and the stop key is to close the water cannon water inlet electric valve.
遙控器為一控四，下方有四個選擇鍵分別對應四臺消防炮，當現場發生火情時，打開相應消防炮進行滅火，調整炮頭對準著火源然后開啟水炮進水閥門，觀察落水點保證覆蓋著火點，如不行則需要調整到合適位置，滅火結束后，關閉進水電動閥門。
The remote control is one control four, and there are four selection keys under it, which correspond to four fire monitors respectively. When a fire occurs on site, open the corresponding fire monitor to extinguish the fire, adjust the gun head to aim at the fire source, and then open the water inlet valve of the water monitor, observe the water falling point to ensure that the fire point is covered. If not, it needs to be adjusted to the appropriate position. After the fire is extinguished, close the water inlet electric valve.
3、消防炮使用完后應用清水沖洗，向注油孔內注油，并檢查各轉動部位是否靈活正常，將炮頭調整向下，然后排空炮塔水管余水。
3. After using the fire monitor, wash it with clean water, fill the oil hole with oil, check whether the rotating parts are flexible and normal, adjust the gun head downward, and then drain the residual water of the turret water pipe.
2、 Maintenance of Chuanxiao electric fire monitor
1、電動防爆消防炮在使用前應先檢查控制器電源電路和無線搖控接收設備,保證電流電壓在正常范圍內.搖控器內電池電量正常。
1. Before using the electric explosion-proof fire monitor, check the power circuit of the controller and the wireless remote control receiving equipment to ensure that the current and voltage are within the normal range The battery power in the remote controller is normal.
2、保持消防炮體清潔，使用泡沫滅火后應用清水沖洗干凈。
2. Keep the fire monitor clean, and wash it with clean water after extinguishing with foam.
3、定期在黃油嘴處及轉動部位加注潤滑脂，保證轉動靈活。
3. Regularly fill grease at the grease fitting and rotating parts to ensure flexible rotation.
4、若發現噴射壓力過高或射程較近時，應檢查噴頭處是否有賭塞物，若有應及時。
4. If the injection pressure is found to be too high or the range is close, check whether there is any blockage at the nozzle, and if so, remove it in time.
5、在安裝消防炮前，要對管路進行沖洗，以防雜物進入消防炮堵塞噴頭。
5. Before installing the fire monitor, flush the pipeline to prevent sundries from entering the fire monitor and blocking the nozzle.
6、各部件應保持完好，如果發現緊固件松動，應及時修復。
6. All parts should be kept in good condition. If fasteners are found to be loose, they should be repaired in time.
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.xintli.net , our staff will contact you in time.
